Showing results: 121 - 135 of 150 items found.
-
DP-VXI-5124 -
Data Patterns Pvt. Ltd.
The Data Patterns DP-VXI-5124 is a VXI 'C' size Carrier Board, which occupies a single slot in the VXI system. The module is a register based device with A16/A24/A32 address space and has interrupter capability. The carrier board's VXI bus interface is used to program and monitor the carrier board registers for configuration and control of the board. The VXI bus interface is also used to communicate with and control the external devices that are connected to an IP modules field I/O signals.
-
Data Patterns Pvt. Ltd.
The VPX standard defined by ANSI/VITA 46.0 is a modern derivative of the older VME standards that is primarily targeted at defence applications, leveraging latest technologies in high speed electronics in order to provide higher performance computing, improved ruggedisation and thermal management capability, higher I/O densities and improved maintainability due to better immunity to ESD. Data Patterns has designed and manufactured a broad range of VPX products required for high end Radar / Electronic Warfare / Image Processing and Sonar applications.
-
Guzik Technical Enterprises
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
DeltaTRAK
This reusable logger can monitor temperature and humidity in facilities, storage and processing areas, clean rooms, labs, and during transport. It is equipped with an external sharp tip probe, providing the option to monitor internal core temperature. Data is available in PDF or spreadsheet format and used for various purposes, such as process or equipment verification and validation, thermal mapping, and documenting environmental conditions to meet GMP, GDP and regulatory compliance. Reports are analyzed to identify trends and patterns, and management decisions can be made to improve practices in areas such as processing and cold chain logistics. Data is easy to archive for record keeping, audits, and compliance with FDA, CDC, HACCP, FSMA and other regulatory requirements.
-
Series 7 -
GOM GmbH
The ATOS ScanBox Series 7 is mainly used in car manufacturing, in try-out toolmaking and in press shops. The optical 3D measuring system performs complete analysis measurements for comparison in the introductory phase or is used for quality control in production. Large parts such as automobile side panels and attached parts of up to 6 m in size can be measured. The full- field measuring data enable the analysis of hole pattern, trimming and character lines. Even heavy and large parts for other applications can be measured and inspected with the ATOS ScanBox Series 7.
-
Piranha4 -
Teledyne DALSA
The Piranha4 cameras offer advanced features such as sub-pixel spatial correction, areas of interest (up to 4 at a time) to reduce data processing and simplify cabling, as well as dual-line area mode to double line rate, HDR mode, shading and lens correction. The Piranha4 is built for the real world with features to ease system integration. The advanced GenICam compliant user interface makes it easy to set up and control camera parameters such as exposure control, FFC, white balance, gain, test patterns, diagnostics and more.
-
ID900 -
ID Quantique SA
IDQ’s Time Controller is an all-in-one device designed for flexibility and it efficiently solves a large number of problems encountered in the laboratory. Its core consists of 4 high-speed (<20 ps precision, 100Mcps rate) inputs and 4 high-speed outputs, interconnected by reconfigurable logic. The Time Controller performs the functions of a number of devices: time-to-digital converter, coincidence counter, delay generator, pattern generator, counter and discriminator. This is complemented by a 10Gbps link to the host computer for fast data transfers, by auxiliary analogue and digital I/O for interfacing with external devices.
-
NI
PXI Digital Waveform Instruments feature up to 32 channels, can sample and generate digital waveforms at up to 200 MHz, and interface with various standard TTL and low-voltage differential signals (LVDS), as well as settable voltage levels. These devices offer per clock cycle, per channel bidirectional control, and phase shifting. They include deep onboard memory with triggering and pattern sequencing. Some models also support doubledatarate (DDR) technology and real-time hardware data comparison. You can use Digital Waveform Devices to create device simulation and complex stimulusresponse tests.
-
50-200/201 -
Pickering Interfaces Ltd.
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
-
81133A -
Keysight Technologies
The Keysight 81133A single-channel 3.35 GHz Pulse Pattern Generator is the latest product in the long history of Keysights high-speed Pulse Pattern Generators. When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. Like its predecessor, the Keysight 8133A, the new 81133A sets the standard for high-speed applications. The Keysight 81133A lets you test your DUT instead of the pulse or data source! For applications that require multiple output channels or multi-level signaling like pre- and de-emphasis (PCI Express) or squelch (Serial ATA), please refer to the 81134A.
-
Eye-BERT 100G -
Spectronix
The Eye-BERT 100G is a low cost, full-featured, stand-alone communication test set with an integrated post equalizer eye opening monitor / scanner. Ultimate flexibility is provided with three different physical interfaces, 13 different configurations, and configurable transmit and receive clocks. The tester supports PRBS patterns up to 263-1 and select data rates from 1.25 to 29Gbps on up to 4 simultaneous channels. Front panel controls are also provided for stand-alone operation. Unlike competing products, fast post equalizer eye monitoring and scanning is included and can be performed on any input channel above 5Gbps.
-
N4952A -
Keysight Technologies
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
dsTest -
Developing Solutions, Inc.
dsTest offers server emulation and client simulation capabilities for comprehensive testing of 3GPP core network interface functionality and performance. Select the interfaces required to accomplish your testing goals–surround a network element with client simulators that simulate client activity, or provision a server emulator with the interfaces necessary to support end-to-end testing, test agents and proxies using both client simulation and server emulation. Test your LTE, EPC, eMBMS, SMS, WLAN Offload, VoLTE and CIoT networks, or gather Big Data to support the identification of patterns and that will provide new business opportunities, revenues, and efficiencies to network operations.
-
Data Patterns Pvt. Ltd.
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
ITS-9050 -
Innovative Technical Systems
The Innovative Technical Systems ITS-9050 Detector is a sensitive, harmonic mixing detector designed to measure millimeter-wave free-space radiation. It is ideal for measuring radiation patterns of antennas inboth the near and far-field. The ITS-9050 employs a free-running dielectric resonator oscillator (DRO) and an integrated harmonic mixer with a waveguide RF input that either connects directly to a circuit under test or to an antenna for radiation detection. The resulting IF is amplified and detected by an IF log-detector that drives a front panel LCD voltmeter to provide an indication of signal strength. A DC output voltage from the log detector is available on a BNC connector to drive external data acquisition instrumentation. Also, a sample of the IF output is provided for measurement on a spectrum analyzer.
